1 最先要依据试验情景
登录路由器进到全局模式去配备enable password 随后储存
# enable password 123
2 破译全过程
（一） 开机后按“ctrl Break”键，进到Rom 监管方式：
System Bootstrap, Version 5.2(5), RELEASE SOFTWARE
Copyright (c) 1986-1994 by cisco Systems
2500 processor with 16384 Kbytes of main memory
Abort at 0x1050450 (PC)
> o/r 0x2142 (忽视Nvram 的正确引导配备信息内容 25系列产品)
>i (重新启动)
（二）重启后，进到配备方式
System Bootstrap, Version 5.2(5), RELEASE SOFTWARE
Copyright (c) 1986-1994 by cisco Systems
2500 processor with 16384 Kbytes of main memory
ERR: Invalid chip id 0x80B5 (reversed = 0x1AD ) detected in System flash
F3: 15020608 968908 947160 at 0x3000060
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software – Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS ™ 2500 Software (C2500-JS-L), Version 12.2(29), RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Wed 11-May-05 13:19 by kellmill
Image text-base: 0x0307D3C0, data-base: 0x00001000
cisco 2500 (68030) processor (revision D) with 16384K/2048K bytes of memory.
Processor board ID 02427741, with hardware revision 00000000
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
1 Ethernet/IEEE 802.3 interface(s)
2 Serial network interface(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read ONLY)
— System Configuration Dialog —
Would you like to enter the initial configuration dialog? [yes/no]: n
enable
config mem (复制Nvram中配备信息内容到memory中)
Conf t
(config)# enable secret cisco (改动动态口令)
(config)# config-register 0x2102 (运用Nvram 的正确引导配备信息内容)
Exit
Copy run start （储存环境变量和新动态口令）
Reload (重新启动，配备起效)
2 下边是2600系列产品的 破译全过程
（一） 开机后按“ctrl Break”键，进到Rom 监管方式：
confreg 0x2142 （26系列）
reset 重新启动
（二）重启后，进到配备方式
enable
config mem (复制Nvram中配备信息内容到memory中)
Conf t
(config)# enable secret cisco (改动动态口令)
(config)# config-register 0x2102 (运用Nvram 的正确引导配备信息内容)
Exit
Copy run start （储存环境变量和新动态口令）
Reload (重新启动，配备起效)
